Pelco Inflatable Bouncy Toy LL27LM User Manual

®
LL27LM  
Mounting Bracket  
Installation/Operation  
C206M (6/93)  
U
®
L
LISTED  
1.0 WARNINGS  
3.0 INSTALLATION  
Prior to installation and use of this product, the follow-  
ing WARNINGS should be observed.  
3.1 INSTALLING THE LL27LM  
BRACKET  
1. Installation and servicing should only be done by  
Qualified Service Personnel and conform to all  
Local codes.  
3.1.1 EH4700L/EH5700L Series  
Enclosures  
To install the LL27LM bracket perform the following  
steps. (Refer to Figure 3.)  
2. Use only installation methods and materials ca-  
pable of supporting four times the maximum speci-  
fied load.  
1. Remove enclosure from pan/tilt, if necessary.  
3. Only use replacement parts recommended by Pelco.  
2. Loosen the two 1/4-20 bolts (item K) from the tilt  
table (item 3) on the bottom of the enclosure.  
Please thoroughly familiarize yourself with the informa-  
tion in this manual prior to installation and operation.  
3. Remove cradle (item 4) and replace with LL27LM  
mounting bracket.  
2.0 DESCRIPTION  
The long arm of the LL27 bracket should be posi-  
tioned over the tilt gear side of the pan/tilt unit.  
The LL27LM mounting bracket is designed to allow you  
to mount an LL27 infrared illuminator to any Legacy®  
Series enclosure. Only one infrared illuminator can be  
mounted to the enclosure/pan and tilt assembly.  
4. Re-attach the tile table (item 3) using the two 1/4-  
20 bolts previously removed.  
Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981  
FAX (800) 289-9150 or (1-559) 292-3827  
International Customers call (1-559) 292-1981 or FAX (1-559) 348-1120  
 
Item 3 Tilt table  
Item 4 Cradle  
Item K Bolt, 1/4-20 x 5/8  
Phillips flat M/S SS  
Figure 3. Legacy® Series Enclosure Exploded Assembly Diagram  
2
3
1
Figure 4. Mounting Bracket Installation  
Pelco Manual C206M (6/93)  
3
 
4.0 WARRANTY AND RETURN  
INFORMATION  
WARRANTY  
3. Details of the defect or problem  
Pelco will repair or replace, without charge, any  
merchandise proved defective in material or workmanship  
for a period of one year after the date of shipment.  
Exceptions to this warranty are as noted below:  
If there is a dispute regarding the warranty of a product  
which does not fall under the warranty conditions stated  
above, please include a written explanation with the product  
when returned.  
• Five years on FT/FR8000 Series fiber optic products.  
• Three years on Genex® Series products (multiplexers,  
server, and keyboard).  
Method of return shipment shall be the same or equal to  
the method by which the item was received by Pelco.  
• Three years on Camclosure® and fixed camera models,  
except the CC3701H-2, CC3701H-2X, CC3751H-2,  
CC3651H-2X, MC3651H-2, and MC3651H-2X camera  
models, which have a five-year warranty.  
RETURNS  
In order to expedite parts returned to the factory for repair  
or credit, please call the factory at (800) 289-9100 or (559)  
292-1981 to obtain an authorization number (CA number if  
returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a  
20% restocking and refurbishing charge.  
Two years on standard motorized or fixed focal length  
lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series  
matrix, and DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20  
scanners, including when used in continuous motion  
applications.  
Goods returned for repair or credit should be clearly  
identified with the assigned CA or RA number and freight  
should be prepaid. Ship to the appropriate address below.  
If you are located within the continental U.S., Alaska,  
Hawaii or Puerto Rico, send goods to:  
Service Department  
Two years on Esprit® and WW5700 Series window wiper  
(excluding wiper blades).  
• Eighteen months on DX Series digital video recorders,  
NVR300 Series network video recorders, and Endura™  
Series distributed network-based video products.months  
on DX Series digital video recorders, NVR300 Series  
network video recorders, EnduraSeries distributed  
network-based video products, and TW3000 Series  
twisted pair transmission products.  
• One year (except video heads) on video cassette  
recorders (VCRs). Video heads will be covered for a  
period of six months.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska,  
Hawaii or Puerto Rico and are instructed to return goods to  
the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send  
the goods to:  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
• Six months on all pan and tilts, scanners or preset lenses  
used in continuous motion applications (that is, preset  
scan, tour and auto scan modes).  
If the goods are to be sent by a FREIGHT FORWARDER,  
send the goods to:  
Pelco will warrant all replacement parts and repairs for 90  
days from the date of Pelco shipment. All goods requiring  
warranty repair shall be sent freight prepaid to Pelco,  
Clovis, California. Repairs made necessary by reason of  
misuse, alteration, normal wear, or accident are not  
covered under this warranty.  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Pelco assumes no risk and shall be subject to no liability for  
damages or loss resulting from the specific use or  
application made of the Products. Pelco’s liability for any  
claim, whether based on breach of contract, negligence,  
infringement of any rights of any party or product liability,  
relating to the Products shall not exceed the price paid by  
the Dealer to Pelco for such Products. In no event will Pelco  
be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of  
third parties) however caused, whether by the negligence of  
Pelco or otherwise.  
(Design and product specifications subject to  
change without notice.)  
The above warranty provides the Dealer with specific legal  
rights. The Dealer may also have additional rights, which  
are subject to variation from state to state.  
If a warranty repair is required, the Dealer must contact  
Pelco at (800) 289-9100 or (559) 292-1981 to obtain a  
Repair Authorization number (RA), and provide the  
following  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or  
Pelco invoice number  
information:  
® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and  
Camclosure are registered trademarks of Pelco.  
™ Endura and ExSite are trademarks of Pelco.  
© Copyright 1993, Pelco. All rights reserved.  
4
Pelco Manual C206M (6/93)  
 

Pentax Camcorder 735 User Manual
Philips Cell Phone Se6 User Manual
Philips Computer Hardware PSC 604 User Manual
Philips TV Antenna SDV2125T 27 User Manual
Pioneer Server ML310 User Manual
Polaris Offroad Vehicle 340 LX User Manual
Polaroid Flat Panel Television FLU 1911SA User Manual
Poulan Blower 530088124 User Manual
Poulan Snow Blower 199340 User Manual
Pride Mobility Mobility Aid Jet 10 User Manual